Commercial insulation in Midland TX - a metal building that holds its temperature
Shop roof sweating, or a workspace you can't keep cool? We insulate metal buildings to fit how you actually use them.
- Licensed and fully insured.
- Free in-person estimates.
- We reply within 1 business day.
How should you insulate a shop or metal building in Midland?
Commercial insulation in Midland, TX means insulating shops, warehouses, offices and metal buildings so the inside doesn't swing between baking and freezing, and in an office or workshop it helps you hold the temperature you set.
Most metal buildings I look at don't need the most expensive option. They need the right one for how they're used. The price moves with the material that use calls for, the size of the building and whether the walls are open framing or already finished. The schedule turns mostly on the city permit, because Midland requires one for work on a commercial building, so we pull it as your contractor and wait for it to be issued before we start. The written estimate gives you your own figure. We're based in Midland and do this work across the cities around it, including Odessa, Big Spring and West Odessa.
How do you know your metal building needs insulation?
Water dripping from the roof
If water falls from the roof panels on cool mornings after a dry night, that's usually condensation forming on the metal, not a leak. Left alone, it rusts fasteners, stains whatever's stored underneath and soaks any insulation already up there.
Too hot to work in
A shop that's fine at eight in the morning and miserable by two is usually taking the sun straight through a bare roof. Every summer it stays that way, you lose working hours or pay to run cooling that can't keep up.
The unit never shuts off
When the heater or AC in an office or workshop runs nonstop and the power bill keeps climbing, the building is usually losing what you pay for through bare metal and gaps. Waiting just means paying that bill again every month.
Moisture work that often goes with it
Crawl space vapor barrier
If an office or rental you own sits over a crawl space, a ground cover down there stops damp soil from feeding moisture up into the floor.
Vapor barrier installation
When a wall or ceiling needs its own moisture layer behind the insulation, this is what keeps condensation off the framing and the metal.
How we handle commercial insulation
The job doesn't start with a material. It starts with how you use the space, because that decides what goes in, faced batts for storage and foam for space you heat and cool. Before anybody seals or sprays, we look hard at gas heaters, old wiring and any old insulation in the building, since closing a building up around a problem only hides it. Then our crew protects your equipment and stock, installs the material across the walls and roof and cleans up behind itself. Open framing makes the work a lot easier, so tell me up front if your walls are already finished.
Moisture is the other half of a metal building job. If you also own an office or rental over a crawl space, a crawl space vapor barrier is often worth doing while we're out, and where a wall or ceiling needs its own moisture layer we handle vapor barrier installation as part of the same plan.
Faced fiberglass batts
These suit a warehouse, storage building or equipment shed you don't fully heat or cool. They cost less and do the job when the goal is taking the edge off heat and cold, not holding a set temperature.
Spray foam
This suits an office, workshop or any space you heat and cool, because it seals air gaps while it insulates. It costs more, so I only point you to it when the way you use the building pays it back.
Get a written estimate for your shop or metal building
Send the form and we'll reply within 1 business day to set up a free in-person estimate, with no pressure to book. You can also call (432) 218-4671.
Call (432) 218-4671Service areas
Why Midland building owners call DraftWise Midland Insulation Solutions
The owner writes your estimate
I used to sell insulation for another company and got tired of watching jobs get oversold, so I come out myself and write up only what your building needs. You get a price from the person who answers for it, not from a salesman.
In business since 2013
I worked on an install crew until I could do the job right myself, then opened our shop in 2013. The person pricing your building has done the work and knows where it usually goes wrong.
Licensed and fully insured
We're licensed and fully insured on every job. On a commercial building that matters, because our crew works up high around your equipment and stock, and that risk shouldn't land on you.
Planned around Midland's codes
The city lists the International Energy Conservation Code and the International Building Code among the codes it has adopted, and the state uses that same energy code for commercial buildings across Texas. We plan your job around them from the estimate on, because permitted commercial work gets inspected.
On a metal building, the material has to fit the way you use it, so send us a few details and I'll come take a look.
What happens after you call about your building?
Call or send the form
Call (432) 218-4671 or use the form and tell us a little about the building. We'll set a time for me to come out.
I look it over in person
I walk the building and check the framing, the heaters and the wiring for anything that needs fixing first. You get a written estimate that spells out what goes in each area and what it costs.
The city reviews the permit
Once you say go, the city's timeline for its review is 7 to 10 business days on alterations and repairs to a commercial building, and 20 business days on a new building or addition. You can follow the status on the city's PermitMidland portal.
Installers work, I check
When the permit is issued, our installers put the job in and clean up. I go over it myself before we call it finished.
Common questions
How much does it cost to insulate a metal building in Midland, TX?
Across the US, insulating a metal building usually costs about $1.50 to $8 per square foot installed, according to one national pricing guide. Where yours lands depends on the material, the size of the building and local labor rates, and finished walls add cost because panels come off or we work around utilities. Call (432) 218-4671 and I'll price your building.
Who can pull a commercial building permit in Midland, TX?
Only a licensed and bonded contractor registered with the City of Midland can get a commercial permit. The permit comes through your contractor, not you, so ask anyone bidding your job whether they're registered with the city.
What causes condensation on the inside of a metal building?
It's usually warm, damp air inside reaching the cold metal skin and turning to water. Fiberglass batts aren't air-tight, so they need a vapor barrier, usually a reinforced foil facing, to keep that air off the metal. If you're comparing batt bids, check that the barrier is in each one.
Can spray foam work as a vapor barrier in a metal building?
Yes, when it goes on thick enough. Spray foam sticks right to the metal skin and closes the air gaps, so it does its own moisture work without a separate layer.
Does spray foam in a commercial building have to be covered?
Usually, yes. A spray foam industry guide says the model building codes require foam to be covered by a thermal or ignition barrier, a fire-resistant layer over the foam, unless the foam is part of an assembly that has passed large-scale fire tests. That covering, or a tested assembly, belongs in any spray foam bid you get.
What is the best way to keep sun heat out of a metal shop roof?
Reflective foil insulation, such as foil-faced bubble wrap, can help when sun coming through the metal roof is the main problem, because it works by reflecting radiant heat. It does its best work in hot, sunny climates, and I'll tell you at the estimate whether it fits your building or whether batts or foam will do more.
Get your shop or metal building insulated
Have the building's use, its rough size and whether the framing is open or finished ready when you call (432) 218-4671 or fill out the form, so I know what to look for before I get there.